How To Install A Electric Hot Water Heater
How to Install an Electric Water Heater
Every bit an Amazon Associate we earn from qualifying purchases. Learn More.
Electrical water heater installation is a great do-it-yourself task. Information technology really isn't every bit hard as y'all may remember. If you're not agape of doing some bones electrical work and plumbing, y'all can salvage yourself some money.
The boilerplate service life of a water heater is between 8 to 12 years. If your heater is reaching erstwhile age, information technology might be fourth dimension to consider a water heater replacement.. Looking at a new free energy efficient model would be a wise selection and an electric h2o heater could save y'all coin in the long run. You lot tin read our reviews of the best electric tankless water heaters on the market today.
How to Install an Electric Water Heater
Once you lot've decided that your best solution is to buy another water heater, information technology's time to become down to the job of getting it installed. Keep in mind, when the job is done, you'll take an former water heater to junk. Hither's a listing of the tools and supplies you'll need to get your electric water heater installed properly:
Consult with a Local Plumber
Get Costless Quotes Today
Pace i: Remove the Erstwhile H2o Heater
- Plow OFF the electricity to the h2o heater at the electrical panel.
- Check the water heater'southward electrical wiring with a voltage detector to make certain that no power is reaching the unit.
- Label the wires with record to marker how they are continued.
- Disconnect the wires.
- Open up the hot water faucet in the house and let it run until the water is absurd.
- Shut OFF the cold h2o supply to the h2o heater.
- Connect a garden hose to the bleed valve.
- Open the valve and drain the tank.
- Open a faucet to allow air into the tank.
- Remove the T&P belch piping from the T&P valve.
- Set the discharge pipe bated to apply later.
- Disconnect the water supply pipes.
- Remove the sometime tank using a hand truck.
Step 2: Install the New H2o Heater
- Set the new tank into a drain pan.
- Install the T&P discharge pipage to the T&P valve.
- Wrap the hot and common cold heat trap nipples with plumbers tape.
- Attach the flexible hoses to the hot & cold oestrus trap nipples. (Use the dielectric fittings if required).
- Line each terminate of the connector body threads with plumbers tape.
- Attach one cease of the connector torso to the flexible hose.
- Hold the hose to the pipage (allow for a little slack) and mark and cut the pipage.
- Remove any burs on the cut pipe.
- Slide the compression nut onto the pipage.
- Press the pipe onto the connector plumbing fixtures and tighten the compression nut.
- Install earthquake straps.
Consult with a Local Plumber
Get FREE Quotes Today
Step 3: Fill the Tank with Water
- Remove the aerator from the nearest faucet and open the hot water side.
- Plough ON the cold water supply to the water heater and check for leaks.
- Fill up the tank full of water. When the water run from the open faucet, the tank is full.
- Exit the faucet open until it stops sputtering.
- Do not connect the electrical wiring until the tank is completely full of h2o.
- Remove the junction box cover and connect the green footing wire to the light-green ground screw.
- Twist the wires together with wire connectors.
- Follow the labels on the wires you marked when yous removed them from your old water heater.
- Replace the junction box embrace and turn ON the power at the electrical console.
- If your h2o heater does not accept ability, exist certain to turn OFF the ability at the electrical console earlier checking your connections.
Watch the Video
Why a New H2o Heater Fails
A new electric water heater is a solid performer and will likely not give you any troubles for the next few years. However, there are a few things you lot should keep in heed before yous cantankerous information technology entirely off your listing. Here are 3 common bug people see later on installing their electric water heater.
- Leaks - a leak is almost always a water supply connection. Double cheque all of your water connections.
- Upper Chemical element - If your water heater tank isn't completely full when you plough the power on, the upper element will "dry fire" and burn out. If this happens to you, the elements are inexpensive and relatively easy to replace.
- Power - A power problem tin be a number of issues. There could be a problem with the wiring in your dwelling house, or the voltage may exist incorrect, information technology could also be as like shooting fish in a barrel every bit flipping the switch in your breaker box. But when it comes to electrical issues, it'southward never a bad thought to call a professional person.
Consult with a Local Plumber
Get Gratuitous Quotes Today
Related Posts
How To Install A Electric Hot Water Heater,
Source: https://www.thinktankhome.com/install-electric-water-heater/
Posted by: stantonsittoss.blogspot.com
0 Response to "How To Install A Electric Hot Water Heater"
Post a Comment